***Order before July 31, 2020 to take advantage of these prices!

Tru-Cut Bandmills

2019 Price List

HS-70 Hydraulic Model - This mill features a 35HP Briggs Vanguard engine. All hydraulic. Hydraulic head lift and power feed. 70” wide max cut capacity. Includes 100’ of #60 roller chain with connector links and bolts to hook up to power feed. The hydraulic features of this mill make it a great value. Does not include track.          

 

$28,000.00

EHS-70 Electric Hydraulic Model – This mill is identical to the model HS-70 except it features a 30HP 3-phase electric motor with a start-stop switch on saw. Includes 50’ of wire between motor and programmable variable frequency drive in a safety disconnect enclosure that can be mounted on a post or wall. This system can be wired for 230 or 460 volts. The customer needs to supply and install a cable and pulley system or a barn door track & trolley system that carries wires. Wires need to be bundled together and hung from cable & track approximately every 6’. Includes 100’ of #60 power-feed chains with connector links and bolts to hook up power feed. Does not include track.

 

$31,750.00

PLS-70 12 Volt Model – The PLS-70 Model features a 35HP Briggs Vanguard engine. This is a more manual bandmill in comparison to the HS-70. This mill is ideal for those only doing occasional cutting and needing a proven saw at a lower cost. Features a 12V DC motor and gearbox for headlift. Manual forward and reverse on track. Other features are identical to Model HS-70. 70” wide max cut capacity.

 

$23,750.00

HS-96 Hydraulic Model - This mill is almost identical to the HS-70 except it is built heavier and geared a bit slower. It also features a 35HP Briggs Vanguard engine. This mill is all hydraulic. Hydraulic is for head lift and power feed. 96” wide max cut capacity. Includes 100’ of #60 roller chain with connector links and bolts to hook up power feed. Please consider everything carefully before choosing this mill; bigger is not always better. You may not want to choose this mill if you only have one log that is too large for the Model HS-70;however, if you have access to a good supply of high value logs and wide crotches too large for the HS-70, the HS-96 may be the fit for you. Track option #1 and concrete log bunks are the only tracks available for this mill. Includes 100’ of #60 power feed chains with connector links and bolts to hook up power feed. Does not include track.

 

$33,000.00

EHS-96 Electric Hydraulic Model – This mill is identical to the model HS-96 except it features a 30HP 3-phase electric motor with a start-stop switch on saw. Includes 50’ of wire between motor and programmable variable frequency drive in a safety disconnect enclosure that can be mounted on a post or wall. This system can be wired for 230 or 460 volts. The customer needs to supply and install a cable and pulley system or a barn door track & trolley system that carries wires. Wires need to be bundled together and hung from cable & track approximately every 6’. This is the same electric motor system that comes with the EHS-70. This mill is like the HS-96; please consider everything before choosing the larger mill. Track option #1 and concrete log bunks are the only tracks available for this mill. Includes 100’ of #60 power-feed chains with connector links and bolts to hook up power feed. Does not include track.

 

$36,750.00

TRACK OPTION #1 For Concrete Slab - This economical track system with a few timber log bunks and chocks supplied by customer is the only track system that is needed for milling table top slabs. The concrete log bunks with log clamps and square arms can be added at any point if you need to mill timbers or regular dimensional lumber. These tracks are 6”x 17.25 lbs per foot. The I-beams are 30’ long and capable of milling 24’6” logs. I-beams have caster rails welded on top, anchoring plates on bottom, braces on sides, stop plates on ends, and chain supports on inside. Comes painted black. Complete with shims and anchor bolts ready to anchor to your slab. Call for pricing on custom lengths.

 

$2,800.00

Concrete Slab Log Bunk #1 with Square Arm and Log Clamp - The purpose of these log bunks is if you already have a track option #1. For concrete slab, you can increase the possibilities by adding these log bunks in addition to log bunks #2. They can be spaced along your track at whatever spacing fits your needs. They are the same heavy-duty design that comes with ground bed. When purchasing a new saw, if you know that you will be needing square arms and log clamps, your 30’ground bed is likely a better option. These log bunks come with shims and anchor bolts ready to bolt to your slab.

For 70"

$1,350.00

For 96"

$1,750.00

Concrete Slab Log Bunk #2 without Square Arm and Log Clamp - These log bunks are only needed when sawing thinner dimensional lumber. Normally spaced at approximately 3’ centers between log bunks #1. Comes complete with shims and anchor bolts ready to be bolted to your slab.

For 70"

$500.00

For 96"

$650.00

I-Beam Ground Track - This is a super heavy-duty log bed with 8”x 31 lbs per foot I-beams for main beams and 6” and 8” I-beam log bunks spaced every 3’ on center. Log bed should be supported every 10’. Raise log bed 6” to 8” above ground or concrete and use leaf blower to keep track cleaned to minimize sawdust buildup on power-feed chains. The number and spacing of square arms and log clamps can be customized according to customer needs, with a minimum of 2 required. Ground bed is priced without square arms and log clamps. Standard length of ground bed is 30”, which gives 24’6” length of cut. Please remember, even though this is a super heavy-duty bed, dropping a 60” diameter oak log on this bed can still damage it!

 

30' Length

$6,750.00

35' Length

$8,375.00

40' Length

$10,000.00

Square Arm and Log Clamps for Ground Bed - These heavy-duty fold down square arms can be raised and lowered with a handle on the operator side of mill and have a jamb bolt to hold them at the proper height. The log clamp slides over against the log on a 1–¾ stress-proof shaft with a binding action, then the cam action handle on log clamp securely clamps log in place. On a standard 30’ ground bed, the standard spacing on square arms and log clamps from end of ground bed is 12-18-21 feet. This allows for cutting logs from 4 to 24 feet in length. For 4’ to 6’ logs, use clamp 18-21. For 8’ to 10’ logs, use clamp 12-18. For 12’ and longer logs, use square arm 12-21 and use log clamp 18 to clamp log.

 

$850.00

If you would like to receive a current price list and/or a brochure, by mail or email, please contact us.

***All prices are picked up at either of our crab Orchard, KY facilities. Call 606-282-8957 for directions. Delivery can be arranged.

 

Terms: 25% down payment when mill is ordered. Balance due at mill manufacturing completion.

Please call for current lead times.

 

Prices effective 5/1/2019. All prices subject to change without notice.    

***Price increase scheduled for 08/01/20***

  • Facebook
  • YouTube

© 2020 Donaldson Machine